BP Mods Pioneer V 1.5 RTA Rebuildable Tank Atomizer for electronic cigarette - 3.2ml
The Pioneer V1.5 RTA by BP Mods is a rebuildable atomizer with a diameter of 22mm created by BP Mods to offer excellent performance in cheek vaping but with the possibility of setting the device for RDL or even lung vaping.
The atomizer is equipped with 2 different bell caps: one for MTL identical to the original Pioneer and an alternative one for DL, also indicated for enjoying tobacco e-liquids to the fullest. Moreover, thanks to the 6 different under-coil air pins ranging from 0.8 - 1.0 - 1.2 - 1.5 - 2.0 - 2.9 mm, the positive post, the blind pin for DL with a large under-coil hole of about 4mm, and the AFC ring for airflow control, you can switch from a super tight draw to a fully lung hit. The bell caps attach to the top cap with two screws and to the deck with threading.
The Pioneer 1.5 is made of stainless steel, has a single coil deck that is almost identical to the previous model (with deeper juice wells), and features a 3.2ml frosted polycarbonate tank. However, the big novelty is the top fill system, which works with the "slide to open" technology already seen in some non-rebuildable atomizers: simply slide the top cap to access the refill area, without the need to disassemble any component. The only precaution is to press down in the opposite direction of the opening, so that the lock is bypassed.
The drip tip consists of a 510 metal base and an interchangeable threaded mouthpiece, and two are included in the package: a long and narrow one for MTL and a short and wide one for RDL / DL. The box also includes a set of spare o-rings and gaskets, four replacement screws for securing the coil in the deck, and three coils:
- 28ga Ni70 Coil (MTL)
- 28ga A1 x 2 + 40ga Ni80 Coil (RDL)
- 26ga A1 x 2 + 40ga Ni80 Coil (DL)
Thanks to the 510 connector, it can be installed on any box mod or tube with the same attachment.
Elegant, versatile, and well-finished: another guarantee for a great vaping experience from BP Mods.
Available in DLC or Stainless Steel version.
Differences between Pioneer V1.5 and Pioneer MTL RTA
- Drip tip frosted
- Top cap sliding opening for refill
- New bell for tobacco and DL
- Deeper liquid wells in the deck
- New seals between deck and tank
- AFC ring with knurling for better grip
- Removable evaporative space compressor to modify aromatic yield
Instructions for use
- Unscrew the bottom part of the atomizer to access the deck
- Regenerate with the preferred coil, insert cotton inside and place the flaps in the liquid wells
- Moisten the cotton with the desired e-liquid
- Screw the tank section back onto the deck
- The top cap opens on the side marked by the engraved dot on the atomizer: press from the opposite side to unlock the system and slide the cap to access the refill compartment
- Fill the tank and close it
- Vape
- To adjust the airflow: use the knurled ring at the base of the atomizer and/or replace the pin with one of those provided (the pre-installed one is the smallest at 0.8mm)
- To change the bell: unscrew the entire metal part above the tank, unscrew the two screws, replace the bell with the alternative one, and repeat the steps in reverse to reassemble everything
Technical Specifications
- Type: rebuildable tank atomizer (RTA)
- Airflow: mouth-to-lung (MTL), restricted direct lung (RDL), and direct lung (DL)
- Materials: stainless steel and polycarbonate
- Diameter: 22mm
- Height: 53.4mm
- Weight: 47g
- Liquid Capacity: 3.2ml
- Liquid Refill: top-fill
- Drip Tip: 510 (interchangeable)
- Connector: 510
- Deck: single coil
- Included Coils: 28ga Ni70 (MTL) - Coil 28ga A1 x 2 + 40ga Ni80 (RDL) - Coil 26ga A1 x 2 + 40ga Ni80 (RDL)
- Airflow Adjustment: under-coil air pin and AFC ring
Package Contents
- Pioneer V 1.5 RTA Atomizer
- Alternative tobacco / DL bell
- Screw-in drip tip for RDL / DL
- Spare deck coil securing screws
- Blind DL pin
- Positive post tower for DL (4mm under-coil hole)
- Tank seals
- Slide to open system seals
- Large spare O-rings
- Medium spare O-rings
- Small spare O-rings
- Air pins under-coil 1.0 - 1.2 - 1.5 - 2.0 - 2.9 mm (0.8mm is pre-installed)
- 28ga Ni70 Coil (MTL)
- Coil 28ga A1 x 2 + 40ga Ni80 (RDL)
- Coil 26ga A1 x 2 + 40ga Ni80 (RDL)
Buy BP Mods atomizers at Svapoebasta
Take a look at the BP Mods atomizers available at the vape shop and choose the perfect one for your e-cig!