copy of Tomcat Bigass Bullets Breakill's Alien Lab Coil Prefatte DL - 2 Pezzi
Breakill's Alien LabTomcat Bigass prefabricated coil Breakill's Alien Lab line Bullets for extreme cloud chasing (DL), only suitable for experienced vapers.
Ready-made coils made with 9 wraps on a 3.5mm complex wire in Ni80: suggested use in dual coil with a total resistance value of 0.34? (160-200W) on mechanical systems with stacked/series batteries and RDA atomizers 25mm and above.
Maximum vapor production.
Packaged in a metal case with 2 pieces.
Handcrafted product made in Italy.
- → Shipping from 9.90 € - info
- → Do you need help? Go to the help center
- → Phone support: +39 392 122 122 8 (Mon-Fri 9:00-12:45 / 15:00-18:00 CEST)
- → Information on warranty and assistance
Breakill's Alien Lab Bullets Tomcat Bigass Ready-made Resistors for Dual Coil - DL Dripper +30mm
The Tomcat Bigass from the Bullets line by Breakill's Alien Lab are ready-made resistors for cloud chasing to be used on mechanical systems with series batteries and on drippers with a minimum diameter of 25mm, exclusively for experienced vapers.
These large-sized resistors (slightly more contained than the Fat Man model) are made with 9 windings of wire in Nichrome 80 on a 3.5mm tip and have a resistance value of approximately 0.34 Ohm when used in pairs. The manufacturer's suggested wattage range for dual coil is 160-200W.
These resistors generate an immense amount of dense, persistent, and abundant vapor, guaranteeing a full and creamy aromatic yield. For a long lifespan (up to 400-700ml of liquid), it is recommended to perform a dry burn every 40-50ml.
The bullet-shaped metal package contains 2 coils.
Technical Specifications
- Inhale type: lung (DL)
- Material: Ni80
- Number of windings: 9
- Internal diameter: 3.5mm
- Resistance value: 0.34? in dual coil
- Wattage range: 160-200W in dual coil
- Suggested atomizers: dual coil RDA of at least 25mm / box with series batteries
- Dry burn: every 40-50ml
- Estimated lifespan: 400-700ml
Instructions for Use
- Place the two coils in the atomizer deck
- Tighten the resistor legs in the appropriate anchor points
- Trim the excess with wire cutters
- Perform several dry activations at a low wattage (half of the recommended wattage) before inserting the cotton and verify that the glow of the windings is uniform (see tutorial)
- Place a generous amount of cotton inside the coils and cut it to size, positioning it properly
- Moisten the cotton with liquid and perform a few activations of the coil to verify its correct functioning
- Close the atomizer and refill the liquid (for tanks)
- Maintenance: perform a dry burn (dry activation without cotton) every 40-50ml of vaporized liquid
Package Contents
- 2 x Tomcat Bigass Coil Breakill's Alien Lab
- 1 x Metal package
All Breakill's Alien Lab ready-made resistors are available on Svapoebasta
On Svapoebasta you can buy these and many other Breakill ready-made resistors for rebuildable atomizers online.
- Packaging
- 2 pieces
- Category
- Prefabricated coil
- Brand
- Breakill's Alien Lab
- Typology
- Standard
- Difficulty
- Difficult
- Type of Shot
- Cheek (MTL)
- Diameter
- 2.5 mm
- Line
- Breakill's Alien Lab - Heroes
- Material
- Ni80 (Nichrome)
You might also like
Feedaty Reviews copy of Tomcat Bigass Bullets Breakill's Alien Lab Coil Prefatte DL - 2 Pezzi
There are no reviews